Vgate12-Way AGM Post Terminal Ends, Battery Terminal Connector Clamps, 8AWG up to 4/0(XL) AWG Gauge, Positive & Negative for SAE/DIN/EN Tapered Top Post

I replaced both of my Optima YELLOWTOP batteries in my Chevy/Duramax 3500 Crew Cab the other day (diesel engines require dual starting batteries) and realized that I was badly needing a clean up of my 12v wiring under the hood.I have added many accessories over the years, including an onboard air compressor for my Grover air horn, a new stereo system with a high output amplifier, front and rear cameras, HID headlights, a 1200 piece starlight headliner, etc., etc., etc. You get the idea. 🤣I found these battery terminals while searching for a solution to the obscene cluster of wiring that was attached to my old battery terminals, as well as to multiple grounding points throughout the engine bay.I compared the design, build quality and customer reviews of many different types of terminals before deciding upon these.These puppies are very well made! Solid aluminum blocks with multiple attachment points for a variety of wire gauges. And, they have well designed terminal clamps that you can actually securely tighten without fear of them snapping in two when applying enough torque to make a tight, complete contact connection with the battery posts.About an hour’s worth of work, some heat-shrink tubing and some quality ring connectors, a few (actually, quite a few) nylon tie-wraps and a roll of wire looming tape and my engine bay is looking (and actually working) MUCH, MUCH better!!! 😄I’ve noticed that my stereo system is actually sounding considerably better than when I was using a chassis ground connection instead of a terminal ground connection.Furthermore, I’m no longer ashamed to open my truck’s hood! 😂Although these are slightly more expensive than some of the other brands out there that offer similarly designed products, I honestly believe these are far and away superior. They’re honestly worth every single penny, and then some!!! 😉I highly, highly recommend these battery terminals!Your engine bay, your battery and even your electronic accessories will ALL thank you!!! 😀

Picked these you to replace my worn out KnuConcepts terminals. 2015 Tacoma w/ 27F battery. Plenty of room in all directions for mounting orientation. Very functional and easy to use in comparison to my old terminals.The listing pictures don't quite do these justice. There is a nice pocket machined on the back around the clamp to accommodate battery posts that may have a lip or shoulder. As well on the back side of the screw block there is a piece of thick plastic attached to mitigate the blocks from shorting out on any metal that may be below them. Lastly there is a bag of star type locking washers for the side screws.The hardware is metric, nuts were 13mm and the hex cap screws are a 5mm Allen. The terminal clamps fit perfectly and are extremely easy to remove and reposition if needed.All in all these are a great value for the money, even compared to the slightly cheaper SHCA blocks.

Nice quality billet aluminum construction. Organized my boat wiring problem. Positive purchasing experience I reccomend this seller.

The first thing to say is that these are large. They work fine, but when you move from the standard single connector to these, they seem massive. It has been noted that the tightening screw on one side will be difficult to tighten if you have a battery that the terminal is recessed. I have recessed terminals and in my case, the negative was inaccessible by the allen wrench. I ended up grinding off part of the short side of the correct allen wrench to tighten the connector onto the terminal. There are plenty of connection points on these to meet almost all your needs. I did pick up some copper washers to put on the post that the "positive fused" cable hooked up because of the way it is designed. That's no fault of these but how the truck manufacturer decided to make the main fused positive connection. For reference, the larger cables are 1/0 AWG and the copper lugs fit without any modification.

Fit nice on my 51R battery terminals. Very useful after a big 3 upgrade. Shiny, good conductivities, seems well made. I like the top and side connectors. Depending on what kinda of terminals and how they are oriented this device makes for a versatile connection.

Seems to be holding tight. After reading some reviews I was worried about it holding tight to batt post. It is very versatile and full of options. Reason I took off a star is cuz I have no use for the negative one. I only needed the positive. This one was perfect for my application so I bought the set anyways and glad I did. Should have the option to just buy one tho.

Works well , wish it had a cover . Easy application on Optima battery

When I put the terminals on it really made things look great , it has extra ports to hook up what you need .Only thing is be very careful the terminals are big and when attached to the battery don't allow another metal to touch the terminals you'll weld the metal to them lol.